Signs of domesticity

I completed the countertops today and that pretty much finishes off the kitchen for the time being. Phew! In a matter of hours Nancy and I were slicing up hors d'oeuvres and making diner in our fancy new kitchen. It feels so good. After dinner I loaded the dishwasher and cleaned up while Nance made a little fire in the woodstove and we shared a little Valentine's Day treat for dessert while we got all sleepy from the fire. We are feeling a lot of gratitude for such a comfortable home.

I'll be working on the stair railing tomorrow.

We had a spider

Morning light on the stairs

A few more small parts and we'll be done for the short term in the kitchen

Another view of the stairs

Hooking up the sink and dishwasher plumbing

My efforts have continued in the kitchen the last few days, mostly hooking up the plumbing, making a back splash for the counter and enclosing/installing the dishwasher. Once the dishwasher was in and a last little bit of cabinet filler was installed on it's right side, we were able to move the refrigerator in from the yurt and finally have all our major appliances and fixtures in and operating. It is not much short of a miracle once again to be able to get water, heat it, make coffee and have refrigerated cream all right in one place and easy to access. I know it's normal and all that, but we've lived for a long time with water out of buckets and all that and now it's just so easy; it almost feels like some sort of embarrassing luxury.

One more coat of finish on the cabinet doors and drawer fronts and we'll call the kitchen "done", at least for a short while. I'll be building an island as soon as we are finished with our obligations to the bank, which should be soon.

Adam finished up a few days ago and now I'll be on my own finishing up the last few projects before we call it good.

Fun stuff

The sink looking all tidy with fixtures and an mineral oil finish on the counters. Note plumbing pieces in the cabinet underneath--water will not be flowing until tomorrow

Fitting the counter and creating necessary openings

This is the counter upside down--making the cut away that goes over and around the lip of the sink

Shaping the opening for the sink. The curved piece in back is a template that I used to router the curved edge

The last two stairs in place. Adam did a really nice job here

I've been working hard on the counter top project, which naturally leads into installing the sink, plumbing the supply lines, and hooking up the dishwasher. It all dovetails as the work progresses.
Shaping the counter tops was careful work and took some time, but it's looking excellent and fitting really nicely, so I am quite pleased. I spent most of today on the plumbing work and tomorrow I should have it all operating. Having our sink, stove, diswasher and fridge all hooked up and running will be monumental.

Adam came back yesterday evening and started up again today. He installed the last two stairs and they look great. Signs of finish everywhere!

Saturday stuff

I was the recipient of an iTouch for Christmas and today I downloaded a free paint app. This is what I came up with

The counter top complete. Next up sanding and final shaping for installation

Messing around with railing ideas

Some of the cabinet doors Nancy is working on

Today was sort of a half-hearted effort on my part as I was sleepy and in need of a nap so I didn't get too much done. Nancy on the other hand has been powering through finish work on the cabinet doors, drawer fronts and cabinet frames. It's all looking really nice. Particularly with stuff like the doors its a lot of work to sand between each coat, but she's making good headway and should have it all ready to go in couple more days.

I completed the counter tops last night and today started in on sanding them down to smooth. Its not so hard as it is a matter of patience just sanding sanding sanding. They're gonna look good when they are done.

Checking for square

The first two pieces joined

There's a lot of clamping, drilling, gluing and screwing in this process

Checking for square. You can see the overlap pattern at the corner. You can also see the first counter section that I built sitting in place on the cabinet--it still needs to be trimmed and sanded before installing

This is my little sketch that sort of shows the plan. There's a gap where the sink will be

The work at the end of the day. I should have the rest built up tomorrow

Today I started building up the second section of maple counter top. This one is a little more complicated then the one featured in the last post, since it encompasses the corner of the cabinetry. Usually, counter tops that turn a corner and cut at a 45 degree angle and joined. In our case we are going to build the corner into the counter as a unit. Adam had the excellent suggestion to "every other" the pieces coming in from each angle and sort of make a weave pattern at the joint.

It's important that the whole thing maintain a nice 90 degree angle so it'll fit into the corner well when its done and I'm glad to say that seems to be working out pretty well.

Maple counter, Cherry landing

Scraping glue drips off the maple counter top

The glue-up process

Adam admiring his work having just put down a coat of poly on the stair landing floor

Today I built up the first section of maple butcher-block style counter top. The process requires drilling out the pieces one-by-one with two different size bits, putting in an anchor screw, taking the screw back out, gluing both boards and then putting them together with screws--about eight holes to a strip of maple. It took quite a long time to build up the section I made today, but that's how it goes. I'm very happy with the result. All that's required now is to trim it to fit and install it.
Tomorrow I'll be working on the section that goes around the sink and turns the corner on the cabinets. It'll be a little more complicated, but after today's work I'm feeling confident about it.

Meanwhile Adam installed the cherry floor on the landing located halfway up the stairs. They look great.

Day by day

Envisioning how I be fastening the maple pieces together for the countertop

The ripped stack of maple

The arced bottom step. The next one up will be similarly arced, although you can tell that from the photo

Adam cutting the radius on the bottom step

Adam is at work shaping the last couple of steps coming down the stairway. These are distinct because the leading edge is curved and they have curved risers underneath coming up to meet them. It took some effort but now they are off to the paint shop (a couple of sawhorses upstairs) for their finish work and then they'll go in soon to finish off the stair project.

I've been working on the counter top project and am making good headway. I took a bunch of 2" x 8" x 8' maple boards, planed them to smooth and then ripped them down into 1 3/4" x 1 3/4" pieces that again had to be planed. The next step is to cut them roughly to length and start gluing them into counters. I'll be doing that tomorrow.

A sign of near completion? Today the technician from the gas company came and hooked up our gas cooktop. We can now cook in our home. Whoo hoo!

Cabinets and Trim

Adam at work on the casing around the pocket doors

Lining up the forstner bit with the pilot hole

Drilling the mounting hole

Doors in place. Notice the red line at the top -- I've yet to adjust these doors so they all line up level

Here I'm using the laser to sight the height line for the drawer slides, one of which is mounted on the left

I've been working on the cabinets, specifically the doors and the drawers. Having never before built cabinetry in any real way I've felt trepidatious at some of the critical junctures. One of those junctures is marking, drilling, and mounting the doors. I spent a good bit of effort to make a couple of jigs that allowed me to make accurate marks for drilling. I tested one door before deciding that my jig was going to work and then after it worked fine went ahead and did the rest. The doors are all mounted with what are known as "European" hinges. They are quite common these days, but used to be somewhat exotic. The beauty of them is that they allow for adjustments in three directions (or more on some models), so if your doors are not all quite straight or a little off center or whatever, you have some room to correct.

I also mounted the slides for all the drawers and that went fine too. Actually, what made it really easy was Adam's laser level. I set it up, found my height and the laser shone its horizontal beam into all the bays of the cabinets and I was able to mark all my drawer heights super accurately. The alternative would have been cumbersome and of dubious accuracy. Hooray for laser levels!

Tomorrow I'll mount the drawers and then make the drawer fronts and finish the cabinet face frame inbetween the doors and drawer fronts. When I get to that point I'm basically done with the major work on the cabinets and will then been getting ready to build the maple countertops.

Working alongside me this week, Adam has been building the framed door passages at both the exit doors and between the office and living space, which is the wall that houses the pocket doors. He's done some nice work and these things all look like pieces of furniture. He'll probably have all the doors trimmed out tomorrow and then be on to running the baseboard that connects it all together.